 |
Rubber Boot
This
accessory will be used as a protective cover against dust and liquids
(waterproof).
$26.00 USD plus shipping
|
|
|
 |
AIR-TEMP Air Temperature Sensor
Perfect
Powers Air temperature sensor a must for boosted applications. Turbo
and supercharger installations aren't complete without this little guy.
Small and easy to fit. NTC or negative temperature coefficient type.
$40.00 USD plus shipping
|
|
|
 |
AMP-2 2.5 Bar Manifold Pressure
Sensor
Manifold
pressure sensor 2.5 bar. Good for 1.5 bar boost pressure. Convenient 12
volt power connection.
$145.00 USD plus shipping
|
|
|
 |
AMP-3 3 Bar Manifold Pressure
Sensor
Manifold
pressure sensor 3.0 bar. Good for 2.0 bar boost pressure. Supplied
together with 5 volt regulator.
$145.00
USD plus shipping
|
|
|
 |
Engine Temperature Sensor -
ENG-TEMP
Perfect
Powers engine temperature sensor. Small and easy to fit. NTC or
negative temperature coefficient type.
$42.00
USD plus shipping
|
|
|
 |
IGN-AMP 7 AMP Ignition Amplifier
7
amp ignition amplifier for injectors or coils, has a heat sink for
disapating heat for high power applications. Easy to install.
$35.00
USD plus shipping
|
|
|
 |
Bosch Injector Clip plus pins
INJCLIP+P Bosch injector clip plus pins
$12.00 USD plus
shipping
|
|
|
 |
Connector plug for Bosch LSU4
Probe
Connector
plug for bosch lsu4 probe including 6 connector pins
$85.00
USD plus shipping
|
|
|
 |
Oxygen Clamp
Narrow
band lambda clamp for de-cat applications.
$25.00
USD plus shipping
|
|
|
 |
SMT6 Shorting (Bridging) Plug
Shorting plug for the Smt6
piggyback chip. Will revert the installation to standard
$30.00 USD plus shipping
|
|
|
 |
SMT8L Shorting (Bridging) Plug
Shorting
plug for the Smt8L piggyback chip. Will revert the installation to
standard.
$30.00
USD plus shipping
|
|
|
 |
SMT8T Shorting (Bridging) Plug
Shorting plug for the Smt8T
piggyback chip. Will revert the installation to standard
$30.00 USD plus shipping
|
|
|
 |
SMT8 Shorting (Bridging) Plug
Shorting
plug for the SMT8 piggyback chip. Will revert the installation to
standard.
Price upon request
USD plus shipping (only special order)
|
|
|
 |
SMT6 Test Jig
The
test jig for the SMT6 to test and ensure that the unit is working
properly
$55.00
USD plus shipping
|
|
|
 |
Trigger Wheel 60
60
tooth trigger wheel made from mild steel. Outside diameter of 170mm
$32.00
USD plus shipping
|
|
|
 |
Trigger Wheel 24+1 54mm
24
+ 1 tooth trigger wheel made from stainless steel. Outside diameter of
54mm. Replacement trigger wheel for some Nissan distributors
$30.00
USD plus shipping
|
|
|
 |
Trigger Wheel 24+1 50mm
24
+ 1 tooth trigger wheel made from stainless steel. Outside diameter of
50mm. Replacement trigger wheel for most Nissan distributors.
$30.00
USD plus shipping
|
|
|
 |
Trigger Wheel 36W
36 tooth trigger wheel made
from mild steel. Outside diameter of 100mm
$32.00 USD plus shipping
|
|
|
 |
Magnetic Crank Sensor
Magnetic
crank angle sensor with 2 signal wires in a screen
$135.00
USD plus shipping
|
|
|
 |
5V Regulator
5
volt regulator to power throttle position sensors or manifold pressure
sensors. Also supplied with a 3Bar Manifold Pressure Sensor - AMP-3.
$65.00
USD plus shipping
|
|
|
 |
WIREX POD
Wireless
pod for communicating with our wireless units.
$145.00
USD plus shipping
|
|
|
 |
USB Cable
USB
communication cable
$20.00
USD plus shipping
|
|
|
 |
SMT8T Communication Cable XY-PC13
SMT8T
communication cable
$24.00
USD plus shipping
|
|
|
 |
SMT6 Communication Cable
Communication
cable for the SMT6 piggyback
$24.00
USD plus shipping
|
|
|
 |
RS232-COMS
RS232
communication cable for MIC3, PRS and XMSV3 Stand Alone units
$24.00
USD plus shipping
|
|
|
 |
Ferrite Core
Ferrite
Cores are used for noise reduction on the USB cable and to help stop
interference with the communication on the USB cable and the LetRipp II
software and unit. We suggest you purchase two of these cores for
either end of the USB cable. A Ferrite core is a passive electric
component used to suppress high frequency noise in electronic circuits
and we have found them most useful when we have experienced
interference between the unit and software through the USB cable.
|